AMS & Color
Bambu Lab AMS alternatives
Before you spend AMS money, work out which half of the job you need. Automatic color changes and dry, organized filament are two different purchases - and only one of them has a cheaper answer.
By Michael W. · Published November 15, 2026

Some links here are Amazon affiliate links, so a purchase may earn this site a commission at no cost to you. It does not change what gets recommended or the order it appears in — how that works.
Quick picks
Tap any row to jump to the full write-up. Prices are read from Amazon and dated; stock is always whatever the listing says.
| # | Product | Best for | Price |
|---|---|---|---|
| 1 | ![]() BIQU BMCU-370 Multi-Color Feeding System The only unit in this registry that adds automatic four-spool switching to a printer you already own, open source, sold as a DIY kit or assembled. | Best third-party alternative The only currently-buyable third-party route to automatic four-spool switching on an A1, A1 mini, P1P or P1S | Check price on Amazon #ad We earn a commission · price as of November 20, 2026 |
| 2 | ![]() EIBOS Cyclopes Four spools dried and fed to the printer at the same time, with an unlimited timer so it can simply stay on as dry storage. | Best if dry filament was the real reason Four-spool drying with a timer that does not force you to restart it | |
| 3 | ![]() Bambu Lab AMS HT One spool, dried hotter than the AMS 2 Pro manages, printed straight from the unit - the right shape for engineering filament. | Best in-family alternative One engineering-grade spool, dried hot, printed straight from the unit | Check price on Amazon #ad We earn a commission · price as of November 20, 2026 |
| 4 | ![]() Polymaker PolyDryer Sealed storage first, active drying second, bought one box at a time - the cheapest way to stop filament going wet rather than fixing it afterward. | Budget pick Sealed storage first, active drying second — the per-spool approach |
The verdict
There is exactly one third-party unit worth naming that adds automatic four-spool switching to a Bambu printer — the BIQU BMCU-370, open source, listed for the A1, A1 mini, P1P and P1S, and in stock at the retailer we checked on 15 November 2026.
For most people asking this question, the cheaper answer is not a color system at all. The AMS 2 Pro's own headline feature is active drying. A four-spool dryer that feeds the printer does that half of the job for far less.
If one difficult material is the reason, buy a single-spool high-temp unit. Bambu publishes 80 C for PA6-CF, PC, ABS and ASA; the standard dryer class stops around 70 C.
If you want colors on a print or two a year, swap by hand. It costs nothing, wastes nothing, and beats every option here on both counts for simple two-tone work.
What this page will not pretend: nothing below replaces an AMS 2 Pro completely. The first-party unit dries, logs material by RFID and switches, and no single alternative here does all three.
What the AMS is known for, and which half you need
Bambu's material system earned its reputation, and the reason it is hard to replace is that it quietly does three jobs at once. Separating them is the whole trick to shopping this category.
Job one: it changes filament on its own. Four spools, automatic switching mid-print, which is what makes multi-color models practical rather than a babysitting exercise. The AMS 2 Pro review is the product page.
Job two: it keeps that filament in a controlled environment. The sealed units monitor humidity, and the 2 Pro actively dries, so the spool you print from is the spool you dried. That is the feature people underestimate when they are shopping and overestimate how cheaply they can replicate.
Job three: it knows what the material is. RFID logging removes the single most common cause of a ruined multi-color print — the wrong material profile. No alternative on this page replaces that, and it is worth being honest about.
Work out which of those three you were paying for. If it is job one, there is one third-party unit and it is the first pick below. If it is job two, you have cheap and good options. If it is job three, you want the first-party unit.
The five honest routes, ranked by what they actually replace
| Route | Changes color automatically? | Dries filament? | Fits what | The catch |
|---|---|---|---|---|
| BIQU BMCU-370 (third-party unit) | Yes, up to four spools | No | A1 mini, A1, P1P, P1S (retailer-listed) | Unsupported by Bambu; DIY variant needs printing and assembly |
| Four-spool dryer that feeds the printer | No | Yes, to about 70 C | Any machine | Replaces the drying half only; nylon and PC need more heat |
| Single-spool high-temperature unit | No | Yes, hotter than the 2 Pro | Any machine | One spool, so no color work at all |
| Sealed modular storage boxes | No | Yes, standard temperature | Any machine | One box per spool; cost grows with the shelf |
| Manual pause-and-swap | No, you do it | No | Any machine | Free and waste-free, but only viable for a few changes |
| A machine with the changer built in | Yes | No | Nothing — it is a new printer | You are buying a printer, not an accessory |
Two rows on that table are not picks on this page because they are not products. Manual swapping is a method, covered in full on multi-color printing without an AMS, and it is genuinely the right answer for a two-tone nameplate: zero purge waste, zero hardware. Buying a machine with a four-spool changer in the box is the other, and the alternatives to a Bambu Lab page covers the machines that do it — the cheapest of them includes a four-spool IFS with automatic color change, which is a different kind of value than bolting a feeder onto a printer you own.
How to choose, in four questions
1. Which machine do you own?
This decides most of it. The third-party unit's retailer compatibility list covers the A1 mini, A1, P1P and P1S — the four most-owned machines, and not the newer ones. On the first-party side the split is strict: AMS and AMS 2 Pro are for the enclosed P and X machines, AMS Lite is the only unit that fits an A1 or A1 mini. The A1 mini page and the P1S page are the per-machine references, and the AMS 2 Pro compatibility page covers the upgrade-kit variants — the buffer is one unit, the hub chains several, and the buffer is a slack manager rather than storage or a dryer.
2. Is it color, or is it moisture?
Be honest about how many multi-color prints you have actually run this year. If the number is under five, the drying and storage half is what you are buying, and the second and fourth picks below do it for a fraction of the money.
3. What materials are in your rotation?
Bambu publishes 50 C for PLA Basic and 65 C for PETG HF in an oven, against 80 C for ABS, ASA, PA6-CF and PC. A standard 70 C-class unit covers the first group properly and misses the second, which is exactly where a single-spool high-temperature unit earns its place. The full table lives on how to dry filament.
4. How much unsupported hardware do you want in the filament path?
Every extra component between the spool and the nozzle is another place a feed problem can start, and that is as true of a third-party feeder as it is of a dryer stack. Filament not feeding is the troubleshooting page, and it is worth reading before you add a link to that chain rather than after.
Where this page sits against its neighbors
Four pages on this site cover this decision and they are not the same page.
This page is the shopping page for not buying the first-party unit.
Multi-color without an AMS is the method page: how to pause, swap and resume, and the honest threshold at about three colors where it stops being viable.
AMS 2 Pro versus AMS Lite is the page for a reader who has already decided to buy first-party and needs to know which unit fits.
AMS mods is the opposite of this page: accessories for an AMS you already own and are keeping.
Who should buy what
You own an A1, A1 mini, P1P or P1S and want automatic color changes cheaply. The third-party unit, with the stock check and the DIY caveat understood.
You print one color at a time and your filament misbehaves. The four-spool dryer, or the sealed boxes if the shelf is the problem rather than the spool in use.
You print nylon, PC or carbon-filled material. The single-spool high-temperature unit, and read the carbon fiber page for the nozzle side of that purchase.
You run multi-color prints weekly and material mix-ups have cost you a print. Buy the AMS 2 Pro. RFID logging is the one thing nothing on this page replaces.
You print two-tone objects occasionally. Swap by hand and spend the money on filament.
What this page is and is not based on
The third-party unit's compatibility list, capacity, drive, firmware claims and kit variants are the retailer's and vendor's published statements from the listing cited below, retrieved 15 November 2026, and its availability was checked the same day before it was featured. Dryer temperatures and capacities are published manufacturer or cited retailer figures held in this site's registry. The per-material drying temperatures are Bambu Lab's own published settings. I have not run the BMCU-370, and no unit on this page has been bench-tested here — there is no test lab behind this site, which is why the reasoning above is mechanism, published specification and fitment rather than results. See how we review.
Every pick in full

Stock photograph of this product class, not of this specific unit.
#ad We earn a commission · price as of November 20, 2026
1. Best third-party alternative
BIQU BMCU-370 Multi-Color Feeding System
The only unit in this registry that adds automatic four-spool switching to a printer you already own, open source, sold as a DIY kit or assembled.
This is the answer to the question most people are actually asking, and for a long time this site had no product to point at. The listing describes it as an open-source alternative to the AMS Lite: up to four spools with automatic switching during a print, a 370 motor with a Hall sensor on this version, and a compatibility list covering the A1 mini, A1, P1P and P1S. It is sold either fully assembled or as a DIY kit where you print the housing and assembly parts yourself — which is a reasonable ask of someone who already owns a working printer.
Why it is ranked first: it is the only route on this page that preserves the thing an AMS actually does. Everything else here replaces the storage and drying half of the job, or moves you to a different machine. If what you want is for the printer to change color on its own, this or a first-party unit are the only two options that do it.
Honest cons, and there are real ones. Nothing about it is supported by Bambu, and fitting a third-party feeder to a closed ecosystem is on you. The DIY variant does not work until you have printed and assembled it. Stock in this category moves fast: on 15 November 2026 the retailer we checked showed ten units left in the warehouse while an Amazon listing for the same system showed unavailable, so verify availability before you commit. And I have not run one — every claim above is the vendor's or the retailer's, which is the standard this site holds itself to on how we review.
What it gets right
- The only third-party unit in this registry that adds automatic four-spool switching to a machine you already own
- Open source, so the firmware and the printed parts are community-maintained rather than locked
- Sold as a DIY kit as well as assembled — and you own a printer, which is the only tool the DIY route needs
What it does not
- Not a Bambu product: nothing about it is supported by Bambu, and fitting it is on you
- The DIY kit requires you to print the housing and assembly parts before anything works
- Stock in this category moves fast — one retailer showed ten units left while an Amazon listing for the same system showed unavailable on the same day, so check before ordering
- I have not run one; the compatibility and reliability claims above are the vendor's and the retailer's, not observations from this site
| Type | Open-source four-spool multi-material feeding system |
|---|---|
| Vendor positioning (cited) | An open-source alternative to the Bambu Lab AMS Lite |
| Compatibility (retailer-listed) | Bambu Lab A1 mini, A1, P1P and P1S |
| Capacity | Up to four spools, with automatic switching during a print |
| Drive (cited) | 370 motor with Hall sensor on the Hall version |
| Firmware (vendor claim) | Open source; stated compatible with official firmware and community updates |
| Supplied as | DIY kit (you print the housing and assembly parts) or fully assembled kit |

2. Best if dry filament was the real reason
EIBOS Cyclopes
Four spools dried and fed to the printer at the same time, with an unlimited timer so it can simply stay on as dry storage.
Read the AMS 2 Pro's own headline feature again: active filament drying. For a large share of the people pricing one, that is the feature they want, and the color changing is a bonus they will use twice a year. If that is you, a four-spool dryer does the same job for a lot less.
The published figures behind this one: up to 70 C, 100 W hot-air heating, a timer that runs from one minute to 24 hours or unlimited, humidity monitoring, and — the part that matters here — it dries and feeds the printer at the same time. The unlimited timer is what turns it from a cycle into dry storage. Note the capacity carefully: four 0.5 kg rolls, or two 1 kg rolls, or one 3 kg roll. “Four spools” is not four kilos.
Honest cons. A 70 C ceiling is the class limit, and it is below what nylon and polycarbonate need — Bambu publishes 80 C for PA6-CF and PC against 65 C for PETG HF and 50 C for PLA Basic in an oven, so this unit covers the common materials and not the engineering ones. The dryer roundup splits the classes, and the budget bracket page covers where this one sits on price. Running a dryer permanently as storage also costs power; a sealed box with desiccant is cheaper for filament you are not about to use.
What it gets right
- An infinite timer means the unit can simply stay on as dry storage, not just run a cycle
- Four spools at a 100 W PTC heater is efficient for the volume it holds
- Direct competitor to the SUNLU S4 at a similar capacity, so shop both
What it does not
- Running a dryer continuously as storage costs power — consider a sealed box with desiccant for long-term storage instead
- Standard-temperature class, so nylon and PC are not its job
- Four-spool footprint again: measure the shelf first
| Capacity | Four spools |
|---|---|
| Heater (cited) | 100 W PTC |
| Timer (cited) | Infinite |

Stock photograph of this product class, not of this specific unit.
#ad We earn a commission · price as of November 20, 2026
3. Best in-family alternative
Bambu Lab AMS HT
One spool, dried hotter than the AMS 2 Pro manages, printed straight from the unit - the right shape for engineering filament.
If you were considering an AMS because of one difficult material rather than because of color, the four-slot unit is the wrong shape and this is the right one. It is a single-spool system with high-temperature active drying that feeds the printer directly, so there is no window where a dried spool sits on a shelf reabsorbing moisture before you use it.
The temperature is the whole argument. Bambu's published drying settings put PA6-CF and PC at 80 C and ABS and ASA at 80 C, while a standard dryer class tops out around 70 C — the same ceiling that makes the four-spool units above the wrong tool for nylon. AMS HT versus a standalone dryer is the page that takes that comparison apart, and the nylon page is the material-specific version.
Honest cons. One spool. It costs real money for a capability a standalone high-temperature dryer also delivers, and the standalone unit does not need to live on the printer. Only worth it if you genuinely print materials that need the extra heat — if your rotation is PLA, PETG and TPU, this is a solution to a problem you do not have.
What it gets right
- Dries at a higher temperature than the AMS 2 Pro, which is what nylon and PC actually need
- Prints directly from the dryer, so there is no window where a dried spool sits absorbing moisture again
- Single spool is the right shape for engineering filament, which you rarely want four of
What it does not
- One spool. If multi-color is the goal, this is the wrong unit entirely
- Costs real money for a capability a standalone high-temp dryer also delivers
- Only worth it if you print materials that genuinely need the extra heat
| Type | Single-spool material system |
|---|---|
| Headline feature | High-temperature active drying |

4. Budget pick
Polymaker PolyDryer
Sealed storage first, active drying second, bought one box at a time - the cheapest way to stop filament going wet rather than fixing it afterward.
The cheapest entry on this page is also the one that reframes the problem. An AMS keeps loaded spools in a controlled environment; the reason that matters is that the rest of your filament is sitting in open air absorbing water. A modular sealed box system attacks that directly: every spool lives sealed, with a cited 10-20% relative humidity reached inside, and you add boxes as the shelf grows.
For a reader who only ever prints one color at a time, this plus a decent dryer is a genuinely complete answer, and it costs a fraction of a four-slot unit. It is also the right first purchase for anyone who keeps rediscovering that their PETG strings after two weeks on a shelf — wet filament symptoms is the page on recognizing that before you blame retraction settings.
Honest cons. Buying enough boxes for a full shelf adds up past the price of a four-spool dryer, and per-box storage takes more total shelf area than a stack. It is standard-temperature drying, so it is not an engineering-filament answer. And it is manual: nothing here changes a color, monitors a print or saves you a trip to the printer.
What it gets right
- The modular box system means every spool lives sealed, which prevents the problem instead of fixing it
- A cited 10-20% RH is the number that matters, and it is a good one
- Cheap to start with one box and add more, instead of one large purchase
What it does not
- Buying enough boxes for a full filament shelf adds up past the price of a four-spool dryer
- Standard-temperature drying — not an engineering-filament answer
- Per-box storage takes more total shelf area than a stacked rack
| Approach (cited) | Passive sealed storage plus active drying |
|---|---|
| Humidity reached (cited) | 10-20% RH |
| Entry point (cited) | From a per-box price, boxes bought individually |
Questions people actually ask
Is there a third-party alternative to the Bambu Lab AMS?
Yes, one worth naming: the BIQU BMCU-370. The retailer listing describes it as an open-source alternative to the AMS Lite, supporting up to four spools with automatic switching during a print, and lists compatibility with the Bambu Lab A1 mini, A1, P1P and P1S. It is sold assembled or as a DIY kit where you print the housing yourself. It is not a Bambu product and nothing about it is supported by Bambu, so fitment and troubleshooting are on you.
What is the cheapest way to print in multiple colors on a Bambu Lab printer?
By hand, and it costs nothing. Pause the print at a layer change, swap the filament, resume - no purge tower, no hardware, no waste. It stops being practical at about three colors or on any design where changes happen on more than a handful of layers, which is the point where a four-spool system starts to pay for itself.
Do I need an AMS to keep my filament dry?
No, and this is the most useful thing on this page. The AMS 2 Pro's headline feature is active drying, but a four-spool dryer that feeds the printer does that job for far less, and a modular sealed box system prevents the problem rather than fixing it. What you lose by going that route is automatic color switching and RFID material logging, not dryness.
Does the BMCU-370 work with a P2S or an H2D?
Not according to the listing we checked. Its stated compatibility covers the Bambu Lab A1 mini, A1, P1P and P1S only. If you own a P2S, X2D or any H-series machine, the honest options on this page are the first-party units, a dryer-based setup for the moisture half of the job, or manual swapping.
Is an AMS alternative worth the risk of unsupported hardware?
It depends on how you value the filament path. Every component between the spool and the nozzle is a place a feed fault can start, and an unsupported feeder means no single company to call when it does. For a reader who enjoys the tinkering and owns a printer to make the parts, the open-source route is genuinely appealing. For a reader who wants the printer to just work, the first-party unit is the cheaper answer once your time is counted.
What does a dryer not replace about an AMS?
Two things. It will not change filament mid-print, so multi-color models still need manual swaps or a four-spool switching unit. And it has no RFID material logging, which is what stops a print being ruined by the wrong material profile. A dryer replaces the moisture and storage half of the AMS's job completely and the color half not at all.
Can a filament dryer reach the temperature nylon needs?
Only a high-temperature one. Bambu publishes drying settings of 80 C for PA6-CF, PC, ABS and ASA, while the standard dryer class - including the four-spool units here - tops out around 70 C. That gap is the whole reason a single-spool high-temperature unit exists, and it is why a long cycle in a 70 C dryer produces nylon that is drier than it was and still not dry enough to print well.
Should I buy a printer with a built-in color changer instead?
Only if you were buying a printer anyway. A machine with a four-spool changer included can be better value than a printer plus a separate color system, and the cheapest one documented on this site includes automatic color change in the box. But it is a whole new ecosystem - no AMS, no Bambu plate, no Bambu profile transfers - which is a much larger decision than adding a feeder to the machine on your desk.
What is the difference between the AMS 2 Pro buffer and hub kits?
The buffer is for one unit and the hub is for several in serial connection, with listed compatibility for the P1P, P1S, X1C and X1E. The filament buffer is a slack manager - it is not storage and it is not a dryer, which is a common misreading of the product name. If you plan to run more than one unit, the hub variant is the one to order.
Sources
- BIQU BMCU-370 Multi Color Feeding System, Hall version: described as "a powerful, open-source alternative to the Bambu Lab AMS lite", supports up to four filament spools with automatic spool switching during a print, 370 motor with Hall sensor, listed compatible with the Bambu Lab A1 mini, A1, P1P and P1S, sold as a DIY kit (housing and assembly parts printed by the user) or fully assembled, stated fully open source and compatible with official firmware as well as community updates. Shown in stock with ten units in the warehouse, a quoted US shipping rate and a 30-day return window - 3DJake BMCU-370 Hall Version listing, retrieved 2026-11-15
- EIBOS Cyclopes published figures: up to 70 C, 100 W hot-air heating, capacity of four 0.5 kg rolls or two 1 kg rolls or one 3 kg roll, timer from 1 minute to 24 hours or unlimited, humidity monitoring, 245 x 305 x 355 mm, 2.0 kg, and the ability to dry and feed the printer at the same time - 3DPrinterGear Cyclopes listing, retrieved 2026-11-07
- Bambu Lab's published per-material drying settings, verbatim: PLA Basic blast drying oven 50 C / 8 h and AMS 2 Pro or AMS HT 55 C / 8 h; PETG HF oven 65 C / 8 h; ABS and ASA oven 80 C / 8 h; PA6-CF oven 80 C / 8-12 h; PC oven 80 C / 8 h - Bambu Lab filament guide, retrieved 2026-10-17
- The AMS 2 Pro upgrade kit ships in two variants - a filament buffer (one unit) and a hub (several units in serial connection) - with listed compatibility for the P1P, P1S, X1C and X1E; the buffer is a slack manager, not storage and not a dryer - 3DJake AMS 2 Pro upgrade kit listing, retrieved 2026-10-17
- FlashForge AD5X: four-spool IFS with automatic color change included in the machine, 220 x 220 x 220 mm, 300 C nozzle, 110 C bed, open structure; shown "In-Stock Now" at 3D Universe with B&H Photo "In Stock" on the same day - availability re-checked 2026-11-15
- Every price shown on a buy button on this page is the live Amazon figure for that listing, refreshed daily and stamped with the date it was checked; a listing with no buyable offer at the last check renders "Check price on Amazon" instead of a number. No price is typed into this copy - see lib/prices.ts
- Capacity, temperature, fitment and feature rows for every product on this page come from this site's product registry, whose spec provenance is documented in content/products.ts - vendor-stated claims are labeled as stated, and no figure is asserted that a manufacturer or a cited third party did not publish
Read this next
- Multi-color printing without an AMSHow to print two or three colors with no AMS and zero purge waste, and the point at which the manual method stops making sense.
- AMS 2 Pro vs AMS LiteThe AMS 2 Pro fits enclosed machines and the AMS Lite fits the A-series. What each does, and the gap you have to fill on an A1.
- The AMS mods worth buyingThe faults worth paying to fix are moisture and desk sprawl. Everything else on the AMS mod lists is a printed bracket and should stay one.
- The best filament dryers in 2026Dryer picks split by temperature range and capacity, because a 70 C unit and a 110 C unit are different products for different materials.
- Bambu Lab alternatives worth shortlistingThree non-Bambu machines that are currently purchasable in the US, each ranked by the one thing it does that no Bambu in this site's registry does - and an honest accounting of the switching cost.
- Bambu Lab AMS 2 ProWhy active drying makes the AMS 2 Pro a different product from the original AMS, and the case for buying it instead of a new printer.