Filament Drying
The best filament dryer under $100
This is one of the few categories where the budget end is the right end. Every unit under this line shares the same ceiling, so capacity and whether you can print from it are the whole decision.
By Michael W. · Published November 7, 2026

Some links here are Amazon affiliate links, so a purchase may earn this site a commission at no cost to you. It does not change what gets recommended or the order it appears in — how that works.
Quick picks
Tap any row to jump to the full write-up. Prices are read from Amazon and dated; stock is always whatever the listing says.
| # | Product | Best for | Price |
|---|---|---|---|
| 1 | ![]() EIBOS Cyclopes Up to 70 C from a 100 W heater, a timer that runs unlimited rather than forcing a restart, humidity monitoring, and it feeds the printer while it dries. | Best overall under $100 Four-spool drying with a timer that does not force you to restart it | |
| 2 | ![]() Polymaker PolyDryer A modular sealed box that stores every spool dry and dries actively when needed, reaching a cited 10-20% RH. You start with one and add boxes. | Best if storage is the real problem Sealed storage first, active drying second — the per-spool approach | |
| 3 | ![]() SUNLU FilaDryer S2 A cited 35-70 C range, one spool, quiet enough to run overnight in a room you sleep in. The cheapest unit here that is a real dryer rather than a warm box. | Budget pick The cheapest dryer worth owning, if you just need PETG and TPU to behave | |
| 4 | ![]() SUNLU FilaDryer S4 Four full 1 kg spools at a published 70 C, with PTFE feed-through to as many as four printers. It sits right at this line and crosses it in both directions. | The one that straddles the line Multi-color and multi-printer owners — four spools dried at once |
The verdict
Buy the EIBOS Cyclopes if you want the most capable unit under $100. Up to 70 C, an unlimited timer so it can stay on as dry storage, humidity monitoring, and it feeds the printer while it dries.
Buy the SUNLU S2 if the budget is the constraint. A cited 35-70 C range on one spool, quiet enough for overnight, and it fixes the problem that brought you here.
Buy the PolyDryer if your filament is getting wet in storage. Sealed boxes at a cited 10-20% RH prevent the problem rather than treating it, one box at a time.
Every unit at this price is a 70 C-class unit. Bambu publishes 80 C drying for ABS, ASA, PC and PA6-CF, so no dryer under this line serves those materials — that is the one thing the line genuinely costs you, and it is not fixable with a longer cycle.
What actually separates dryers at this price
Three specifications decide this bracket, and the one most listings lead with is not among them.
1. The ceiling, which is the same everywhere under the line
Every unit here tops out around 70 C. That is not a defect, it is the class: PLA, PETG and TPU all dry comfortably below it, and Bambu's own published settings put PLA Basic at the bottom of the scale at a 50 C oven figure. Where it becomes a hard wall is engineering filament — Bambu publishes 80 C for ABS, ASA, PC and PA6-CF, and the MatterHackers PA6-CF listing specifies 80 C for 8-12 hours. A 70 C cycle run for longer removes less water, not the same water more slowly.
So the honest framing for this page is: if your difficult material is nylon, polycarbonate or anything carbon-filled, stop reading and go to the nylon roundup, which covers the units that reach those figures and costs well above this line. The carbon fiber page sets out why drying is one of four published requirements for those filaments.
2. Capacity, counted in the spools you actually load
This is where the listings mislead. “Four spools” can mean four half-kilo rolls or four 1 kg rolls, and on one of the picks above it means the former. Check the stated roll weight and the maximum spool dimension, not the slot count. If you run four-color jobs, drying one spool while three sit in open air is close to pointless — the cabinet page is the argument for capacity as the deciding feature.
3. Whether you can print from it
The gap between a finished cycle and the start of a print is where the work quietly comes undone, especially with TPU and PETG in a humid room. A unit with filament outputs and PTFE routing closes that window; a sealed box without them does not. Two of the picks above publish feed-through and one does not, and at this price that is the most useful dividing line of the three.
Side by side
| SUNLU S2 | Polymaker PolyDryer | EIBOS Cyclopes | SUNLU S4 (at the line) | |
|---|---|---|---|---|
| Temperature | Cited 35-70 C | Standard-temperature class | Up to 70 C | 70 C maximum |
| Capacity | One spool | One spool per box, modular | Four 0.5 kg or two 1 kg or one 3 kg | Four 1 kg spools |
| Heater | Not published by a source we fetched | Not published by a source we fetched | 100 W hot air | PTC, 320 W in both spec tables; 300 W and 330 W elsewhere |
| Timer | Not published by a source we fetched | Not published by a source we fetched | 1 min to 24 h, or unlimited | Not published by a source we fetched |
| Humidity | Not published by a source we fetched | Cited 10-20% RH reached | Humidity monitoring | Automatic control, starts 30-50%, stops 25% |
| Feeds printer while drying | No | Not published by a source we fetched | Yes | Yes, up to four printers |
| Size | Not published by a source we fetched | Not published by a source we fetched | 245 x 305 x 355 mm | 516 x 278 x 350 mm or 458 x 218 x 312 mm, depending on the retailer |
| Weight | Not published by a source we fetched | Not published by a source we fetched | 2.0 kg | 4.8 kg |
| Reaches the published 80 C for nylon and PC | No | No | No | No |
| Under the $100 line at the last check | Yes | Yes | Yes | Straddles it |
What a cheap dryer actually fixes
Worth being specific, because the category is sold on vague promises. Filament that has absorbed water prints with surface popping and fine hairs between features, rough or bubbled walls, poor adhesion between layers, and in bad cases a brittle strand that snaps in the feed path. TPU and PETG show it first; nylon shows it worst.
A 70 C-class unit removes that water from PLA, PETG and TPU, and it does so for a fraction of the cost of the printer. That is the entire case for the bracket, and it is a strong one. How to dry filament covers doing it properly, including the per-material settings, and wet filament symptoms is the diagnosis page if you are not sure the problem is moisture at all.
What it does not fix: a worn nozzle, a dirty plate, a bad profile or a draft from an open window. Those get misdiagnosed as wet filament constantly, and buying a dryer for them is money spent on the wrong fault.
The alternatives at this price, honestly
An oven, if you already own the right one
Bambu's own guidance is a blast or forced-air drying oven with even temperature distribution, with the filament kept away from the heating element. A kitchen oven is not that, and its thermostat swings wider than the margin a spool of PLA tolerates. Drying filament in an oven works through where that does and does not hold.
The printer's own heatbed
Free, with published settings for the X1 series, and genuinely limited: it occupies the machine, and the A1 mini's 80 C bed ceiling sits below Bambu's published heatbed figures for everything above TPU. Drying filament in the printer is the page, and the under-$500 printer roundup is where those bed ceilings are compared.
An AMS 2 Pro, if color is also on your list
Well above this line, and it replaces two purchases: it dries four spools actively and changes between them automatically on the machine it is attached to. If you were going to buy a four-spool dryer and a color system anyway, compare the two routes before buying the cheaper half first — the AMS 2 Pro review and drying inside an AMS are the pages for that.
Who should buy which
One printer, one color at a time, tight budget. The S2. It is the whole fix for the common problem.
You want the box to stay on as storage and feed the printer. The Cyclopes, for the unlimited timer and the feed-through.
Your filament is getting wet sitting on a shelf. The PolyDryer, because prevention beats treatment and you can start with a single box.
You run four full-size spools. The S4, if the button has it under the line when you read this; otherwise plan for it as the next step up.
You print nylon, PC or anything carbon-filled. Nothing here. The published requirement is 80 C and this whole bracket tops out at 70 C. The SUNLU E2 review covers the unit that does reach it, well above this line.
What this page is and is not based on
Cyclopes figures come from the 3DPrinterGear listing retrieved 7 November 2026, which showed the unit out of stock at that retailer — said out loud above, because the buy row here points at the Amazon listing, which carried a live price at the last daily check. S4 figures come from the MatterHackers and 3DJake listings retrieved 31 October 2026; where they disagree, both figures are printed. S2 and PolyDryer rows are cited registry figures whose provenance is documented in content/products.ts, and the rows no source published are marked rather than estimated. The 80 C drying requirement comes from Bambu Lab's own published per-material settings and the MatterHackers PA6-CF listing. The $100 line was set and verified against the live Amazon figures in this site's price layer on 7 November 2026, and no other dollar amount appears in this copy. I have not run these units side by side, measured a humidity reading or timed a cycle: there is no test lab behind this site. See how we review.
Every pick in full

1. Best overall under $100
EIBOS Cyclopes
Up to 70 C from a 100 W heater, a timer that runs unlimited rather than forcing a restart, humidity monitoring, and it feeds the printer while it dries.
This is the unit that does the most under the line. 3DPrinterGear lists the Cyclopes at up to 70 C from a 100 W hot-air heater, with a timer of 1 minute to 24 hours or unlimited, humidity monitoring, a product size of 245 x 305 x 355 mm at 2.0 kg, and a stated ability to dry and feed the printer at the same time. Its stated capacity is four 0.5 kg rolls, two 1 kg rolls or a single 3 kg roll.
Two of those specifications matter more than the rest. The unlimited timer means the box can simply stay on as dry storage instead of running a cycle and stopping, which is the difference between fixing wet filament and preventing it. And feeding through while drying closes the window where a freshly dried spool sits on the bench reabsorbing water before the print starts — printing while drying is the page on that approach.
Honest cons, and the capacity one catches people. “Four spools” here means four half-kilo rolls; standard 1 kg spools fit two at a time. Running a dryer permanently as storage costs power, and a sealed box with desiccant does that job without a heater — dryer boxes covers the trade. One retailer showed the unit out of stock when this page was written, while the Amazon listing behind the buy row had a live price at the last daily check; buy from whichever is actually in stock when you read this.
What it gets right
- An infinite timer means the unit can simply stay on as dry storage, not just run a cycle
- Four spools at a 100 W PTC heater is efficient for the volume it holds
- Direct competitor to the SUNLU S4 at a similar capacity, so shop both
What it does not
- Running a dryer continuously as storage costs power — consider a sealed box with desiccant for long-term storage instead
- Standard-temperature class, so nylon and PC are not its job
- Four-spool footprint again: measure the shelf first
| Capacity | Four spools |
|---|---|
| Heater (cited) | 100 W PTC |
| Timer (cited) | Infinite |

2. Best if storage is the real problem
Polymaker PolyDryer
A modular sealed box that stores every spool dry and dries actively when needed, reaching a cited 10-20% RH. You start with one and add boxes.
The registry records the PolyDryer as a passive sealed storage system with active drying, reaching a cited 10-20% relative humidity, bought a box at a time. That last part is the reason it belongs on a page about this price bracket: the entry point is a single box rather than one large appliance.
The logic here is different from every other pick. The others treat a wet spool; this one is built so the spool never gets wet. For anyone whose filament lives in open air between prints, prevention is the cheaper fix, and a cited 10-20% RH is a good number to prevent at. Wet filament symptoms is the test for whether you have an active problem or a storage one.
Where it stops being the cheap answer is scale. Buying boxes for a whole shelf adds up past the price of a single four-spool unit, and per-box storage takes more total shelf area than a stack. It is also standard-temperature, so it is not the engineering filament answer any more than the rest of this page is.
What it gets right
- The modular box system means every spool lives sealed, which prevents the problem instead of fixing it
- A cited 10-20% RH is the number that matters, and it is a good one
- Cheap to start with one box and add more, instead of one large purchase
What it does not
- Buying enough boxes for a full filament shelf adds up past the price of a four-spool dryer
- Standard-temperature drying — not an engineering-filament answer
- Per-box storage takes more total shelf area than a stacked rack
| Approach (cited) | Passive sealed storage plus active drying |
|---|---|
| Humidity reached (cited) | 10-20% RH |
| Entry point (cited) | From a per-box price, boxes bought individually |

3. Budget pick
SUNLU FilaDryer S2
A cited 35-70 C range, one spool, quiet enough to run overnight in a room you sleep in. The cheapest unit here that is a real dryer rather than a warm box.
If the budget is the binding constraint, this is where to start. The registry records a cited 35-70 C range, single-spool capacity, support for the common filament diameters, and that it is quiet enough for overnight drying. That range covers PLA, PETG and TPU, which is the overwhelming majority of what actually goes wet in a hobby workshop.
The reason it stays on this list rather than being beaten by the pricier picks is honesty about what most people need. A single spool treated properly, overnight, in a quiet box, solves the stringing-and-popping problem that sends people to this category in the first place. Whether a dryer is worth it is the page to read before spending more than this.
Its limits are real and they are the limits of its class: a 70 C ceiling, one spool, and no feed-through, so there is a window after every cycle in which the spool is reabsorbing. If any of those three bother you, one of the picks above fixes it without leaving this price bracket.
What it gets right
- 35-70 C covers PLA, PETG and TPU, which is most of what actually goes wet in a hobby workshop
- Quiet enough to run overnight in a room you sleep in
- The cheapest entry point that is still a real dryer rather than a warm box
What it does not
- 70 C ceiling means nylon, PC and PA-CF are out of range
- One spool at a time, which does not fit a four-color job
- No printing from the unit, so a dried spool starts re-absorbing the moment it comes out
| Temperature range (cited) | 35-70 C |
|---|---|
| Capacity | One spool |
| Diameters | Supports all common filament diameters |
| Noted | Quiet enough for overnight drying |

4. The one that straddles the line
SUNLU FilaDryer S4
Four full 1 kg spools at a published 70 C, with PTFE feed-through to as many as four printers. It sits right at this line and crosses it in both directions.
This pick is here because pretending it is not would be dishonest. The S4 is the four-spool box in this family: MatterHackers lists a 70 C heating temperature, PTC heating with three fans, an interior balance within ±3 C of the set temperature, four standard 1 kg spools, automatic humidity control between 25% and 50%, and the ability to feed as many as four printers. 3DJake adds heat-up times of 30 minutes to 50 C and 50 minutes to 70 C, and a maximum spool size of 75 x 206 mm.
Its live price has sat within a few dollars of this page's line, above it some weeks and below it others, which is exactly why it is labeled rather than ranked. If the button shows it under the line when you read this and you run four full-size spools, it is the most capable thing on the page. If it is over, the Cyclopes does most of the same work at half the capacity. The full S4 review has every published figure, including the two specs its retailers disagree on.
Two further costs worth knowing: four spools of thermal mass heat slowly, so this is an overnight appliance rather than a between-prints one, and it is a large box that needs measured shelf space next to the printer.
What it gets right
- Four spools at once is the only capacity that matches a four-color workflow
- Dries the whole set you are about to print with, rather than one spool at a time while three re-absorb
- Cheaper per spool than any single-spool dryer
What it does not
- It is a big box; four-spool dryers need shelf space you may not have next to the printer
- Standard-temperature drying is not enough for nylon or PC — that needs a high-temp unit
- Four spools heat more slowly than one, so cycles are long
| Capacity | Four spools |
|---|---|
| Positioning (cited) | Best for multi-color and multiple printers |
Questions people actually ask
What is the best filament dryer under $100?
The EIBOS Cyclopes, for most people. 3DPrinterGear lists it at up to 70 C from a 100 W hot-air heater with a timer of 1 minute to 24 hours or unlimited, humidity monitoring, and a stated ability to dry and feed the printer at the same time. The unlimited timer is what lets it double as dry storage rather than only running a cycle.
Is a cheap filament dryer worth buying?
For PLA, PETG and TPU, yes - this is one of the few categories where the budget end is the right end. Those materials dry well inside the 70 C ceiling every unit at this price shares, so a cheap dryer removes the water that causes popping, stringing and weak layer adhesion for a small fraction of what the printer cost. For nylon or polycarbonate it is not worth buying, because the published requirement is above the class.
Can a dryer under $100 dry nylon or PA6-CF?
No. Bambu publishes 80 C drying for ABS, ASA, PC and PA6-CF, and the MatterHackers PA6-CF listing specifies 80 C for 8-12 hours. Every unit under this line tops out around 70 C, and running a 70 C cycle for longer removes less moisture rather than the same amount more slowly. That material group needs a higher-temperature unit or the AMS HT.
How many spools can a dryer at this price hold?
Between one and four, and the slot count is the specification most likely to mislead you. The Cyclopes is stated as four 0.5 kg rolls, two 1 kg rolls or one 3 kg roll - so 'four spools' means half-kilo spools. The S2 is a single-spool unit. Check the stated roll weight and the maximum spool dimension rather than the number of slots.
Can you print directly from a filament dryer under $100?
From some of them. 3DPrinterGear states the Cyclopes dries and feeds the printer at the same time, and the S4 publishes PTFE feed-through to as many as four printers. The registry records no printing from the S2. It matters more than it sounds: the gap between a finished cycle and the start of a print is when a dried spool starts reabsorbing moisture.
Dryer or sealed storage box?
A dryer removes moisture; a sealed box with desiccant stops it coming back. If your spools are getting wet on an open shelf, prevention is the cheaper fix and the PolyDryer's modular boxes are built for exactly that, at a cited 10-20% RH. If you already have wet filament printing badly, you need the heat first. Many workshops end up with both.
How current are the prices on this page?
Every number is read from Amazon's own data by this site's price layer, refreshed daily and shown beside the date it was last checked; nothing is typed into the copy. The $100 threshold was verified against those live figures when this page was published, with headroom on the three picks marked as under the line. The S4 sits close enough to move across it, which is why it is labeled rather than ranked.
Will an AMS 2 Pro replace a dryer?
For four spools on one Bambu machine, largely yes - it dries actively and changes filament automatically, which is two purchases in one unit. It costs well above this line, it is a printer accessory rather than a bench appliance, and it does not reach the 80 C that nylon and PC publish. If you feed more than one printer, a standalone dryer is the more useful box.
Sources
- EIBOS Cyclopes maximum temperature up to 70 C, 100 W hot-air heating, stated capacity of four 0.5 kg rolls or two 1 kg rolls or one 3 kg roll, timer of 1 min to 24 h or unlimited, humidity monitoring, product size 245 x 305 x 355 mm, 2.0 kg total weight, and a stated ability to dry and feed the printer at the same time - 3DPrinterGear EIBOS Cyclopes listing, retrieved 2026-11-07. That retailer showed the unit Out of Stock; the Amazon listing behind the buy row here carried a live price at the last daily price check, which is the availability test used on this site
- SUNLU FilaDryer S4 heating temperature 70 C, rated power 320 W in the technical specifications with 300 W and 330 W given elsewhere on the same page, PTC heating with three fans, interior temperature balance within +/-3 C of the set temperature, capacity four standard 1 kg spools, external dimensions 516 x 278 x 350 mm, 4.8 kg product weight, automatic humidity control between 25% and 50%, and the ability to feed filament to up to four 3D printers - MatterHackers SUNLU FilaDryer S4 listing, retrieved 2026-10-31
- SUNLU FilaDryer S4 maximum 70 C with heating times of 30 minutes for 25-50 C and 50 minutes for 25-70 C, 4 x 1 kg spool capacity with a maximum spool size of 75 x 206 mm, device dimensions 458 x 218 x 312 mm, internal size 450 x 210 x 211 mm, and automatic humidity control that starts at a preset 30-50% and stops at 25% - 3DJake SUNLU FilaDryer S4 listing, retrieved 2026-10-31
- Bambu Lab's own published per-material drying settings - PLA Basic at a 50 C blast drying oven setting at the bottom of the scale against ABS, ASA, PC and PA6-CF at 80 C - reproduced in full on this site's drying pages. Bambu Lab filament guide, retrieved 2026-10-17
- Bambu Lab PA6-CF published drying setting of 80 C for 8-12 hours - MatterHackers Bambu Lab PA6-CF 1 kg listing, retrieved 2026-10-31
- Every price shown on this page is the live Amazon figure for that listing, refreshed daily and stamped with the date it was checked; a listing with no buyable offer at the last check renders "Check price on Amazon" instead of a number. The $100 line was set and verified against those live figures on 2026-11-07. No price is typed into the copy - see lib/prices.ts
- Cited capacity, temperature-range and approach rows for the SUNLU S2, the Polymaker PolyDryer, the AMS 2 Pro and the AMS HT come from this site's product registry, whose spec provenance is documented in content/products.ts - no figure is asserted that a manufacturer or a cited third party did not publish
Read this next
- The best filament dryers in 2026Dryer picks split by temperature range and capacity, because a 70 C unit and a 110 C unit are different products for different materials.
- SUNLU FilaDryer S4Four 1 kg spools at a published 70 C, with filament fed out to up to four printers while it dries. The specs, the two figures retailers disagree on, and who should skip it.
- Filament dryer boxesHow per-spool sealed boxes differ from four-spool dryers, the humidity figure that matters, and where the modular approach stops scaling.
- Is a filament dryer worth it?Who a dryer genuinely pays for, who should buy sealed storage instead, and the free test that settles it before you spend.
- The best Bambu Lab printer under $500Three machines under the line share a published 300 C nozzle. The enclosure, the bed size and the bed ceiling are what separate them - and what you should spend the leftover money on.
- The best Bambu Lab upgrades under $100Six upgrades under the line, ranked by what each one fixes: the touchscreen a P1S never had, the hotend that unlocks abrasive filament, cooling, plates and the wear part.