Printers
Bambu Lab vs FlashForge
Two FlashForge machines are worth a Bambu owner's attention, and for opposite reasons. One is cheaper than the color system you already own. The other does something no AMS can do.
By Michael W. · Published October 24, 2026

Some links here are Amazon affiliate links, so a purchase may earn this site a commission at no cost to you. It does not change what gets recommended or the order it appears in — how that works.
The verdict
If you own a Bambu machine, neither FlashForge replaces it. Both published four-color machines here are open frame, so neither covers ABS or ASA, and nothing from the AMS, plate or Panda shelf transfers.
Buy the AD5X only as a cheap second color machine. 3D Universe lists it at a 220 mm cube with four spools included, a 300 C nozzle and a 110 C bed. It is a small PLA and PETG color printer and it is honest about that.
Buy the Creator 5 if purge waste is the thing you actually hate. Four independent toolheads at a 256 mm cube change material without flushing one nozzle, and they make soluble support in a second polymer practical. No AMS does that.
Nothing here is a reason to leave the ecosystem. If the complaint is enclosure, screen or nozzle swap, the in-family answers are a P2S or an X2D, not a brand change.
Side by side
| FlashForge AD5X | FlashForge Creator 5 | Bambu Lab A1 | Bambu Lab P1S | |
|---|---|---|---|---|
| Build volume | 220 x 220 x 220 mm | 256 x 256 x 256 mm | 256 x 256 x 256 mm | 256 x 256 x 256 mm |
| Nozzle ceiling | 300 C | 320 C | 300 C | 300 C |
| Bed ceiling | 110 C | 120 C | 100 C | 100 C |
| Enclosure | Open structure | Open frame, no active heating | Open frame | Enclosed |
| Multi-material | IFS, four spools, one nozzle | Four independent toolheads | AMS Lite, four spools, one nozzle | AMS and AMS 2 Pro fit it |
| Purge on color change | Yes - shared nozzle | No - toolhead swap | Yes - shared nozzle | Yes - shared nozzle |
| Machine size | 363 x 376 x 413 mm | 436 x 432 x 480 mm without accessories | 465 x 410 x 430 mm | 389 x 389 x 458 mm |
| Net weight | 11 kg | 14 kg | 8.3 kg | 12.95 kg |
| Screen | 4.3-inch touchscreen | 4-inch touchscreen | Not published by a source we fetched | No touchscreen |
| Camera | Optional | Built-in, 1280 x 720 at 30 fps | Not published by a source we fetched | Not published by a source we fetched |
| Third-party parts | Thin | Thin | Deep | Deepest in the range |
The enclosure is the real dividing line
Every row in that table is secondary to one fact: the P1S is enclosed and all three of the others are not. That is not a small difference dressed up as a big one. An enclosure traps the heat the bed and hotend already produce, which keeps the air around a tall part warm enough that the layers below do not contract while the layers above are still being laid down. Without it, ABS and ASA split along layer lines and lift off the plate, regardless of what the nozzle can reach.
So the AD5X's 110 C bed — genuinely the hottest bed of the two cheap machines here, hotter than either Bambu figure — buys better adhesion on the first layer and does nothing about the thirtieth. The Creator 5's 320 C nozzle and 120 C bed are the hottest numbers on the page and sit on an open frame; FlashForge puts the heated chamber on the Creator 5 Pro, not the standard model.
If engineering material is why you are reading this comparison, the honest answer is that none of these three is the machine for it, and the in-family route is the ASA and ABS pick or the chamber-heated machines covered on X1C versus X1E and what replaced them.
Toolheads against a shared nozzle
What an AMS actually costs you per color change
A single-nozzle multi-color system has to empty the previous material out of the hotend before the next one arrives, or the colors blend. That purge is filament you paid for, deposited into a tower you throw away, and it happens at every single change. On a four-color print with a lot of alternation, the tower can rival the part.
The AD5X and the A1 both work this way, through the IFS and AMS Lite respectively. So does a P1S with an AMS 2 Pro. It is the normal cost of color and most people decide it is worth paying.
Why four toolheads is a different machine, not a better one
The Creator 5's four independent toolheads remove the flush, because the next material is already loaded in its own hotend at its own temperature. That is the capability, and it brings a second one with it: a soluble support material like the PVA or BVOH FlashForge lists can be held hot in its own toolhead, which makes genuinely dissolvable support structures practical rather than theoretical.
The flip side is maintenance surface. Four hotends is four nozzles to clog, four to clean and four to eventually replace, and a tool-changing mechanism is a moving interface that a fixed head does not have. Nobody who has spent an evening on one clogged nozzle should skip past that sentence.
Where Bambu's answer stops
Bambu's route to the same problem is two nozzles rather than four, on the H2 series and the X2D. What dual nozzles actually change explains the difference between two hot materials and four cold spools feeding one nozzle. Two is a smaller answer than four, and it arrives attached to the ecosystem, the profiles and the parts shelf.
Who should actually buy a FlashForge
Three narrow cases, and they are narrow on purpose.
You want a second color machine for small PLA parts and the budget is the constraint. The AD5X includes its four-spool system and publishes a hotter bed than either Bambu here. As an additional machine beside something enclosed, the ecosystem objection mostly evaporates.
Purge waste is your actual, measured complaint. If you print multi-color often enough that the towers bother you, the Creator 5's architecture addresses the cause rather than the symptom, and no AMS upgrade will.
You need dissolvable support in a second polymer. Four independently heated toolheads make that routine. A single-nozzle machine with four spools does not.
Everyone else is better off spending the same money inside the ecosystem. AMS 2 Pro compatibility covers adding four dried spools to a machine you already own, and the best-value pick is the honest read on which Bambu machine to buy if you are replacing rather than adding. If you are weighing the whole field rather than this one brand, Bambu Lab alternatives ranks every currently-buyable machine that beats the lineup at something specific.
What this page is and is not based on
AD5X figures — the 220 mm cube, 300 C nozzle, 110 C bed, four-spool IFS, 4.3-inch screen, optional camera, open structure, 11 kg and 363 x 376 x 413 mm — come from the 3D Universe AD5X listing retrieved 24 October 2026, which also showed the machine in stock. The 600 mm/s and 20,000 mm/s² figures and the material list come from the 3DJake AD5X listing, same date, which shows it sold out there; the conflicting 300 mm/s printing figure is flagged in the text rather than resolved, because we have not measured it. Creator 5 figures come from FlashForge's own product page, same date, which showed it in stock. Adventurer 5M figures come from the 3DJake listing, same date. Bambu figures come from the Makerpoint P1S listing and the 3DJake A1 and P2S listings retrieved 11 October 2026. AMS behavior and third-party fitment are registry spec rows whose provenance is documented in content/products.ts. I have not run an AD5X, an Adventurer 5M or a Creator 5, and have not run any of these machines side by side: there is no test lab behind this site, no stopwatch and no sound meter, which is why every number above carries a source and the rows nobody published are left empty. See how we review. No price appears in prose.
The two machines, side by side

1. Best for almost everyone reading this
Bambu Lab P1S
A 256 mm enclosed cube with the deepest parts and profile ecosystem in desktop printing. Neither FlashForge is enclosed, and that decides most of this.
The honest summary first: on a specification table, the FlashForge machines look like strong value, and on one axis they genuinely are. What the P1S wins is not a number. Makerpoint lists it at a 256 x 256 x 256 mm build volume, a 300 C nozzle and a 100 C bed, inside an enclosure. 3D Universe lists the AD5X at a 220 mm cube with the same 300 C nozzle, a hotter 110 C bed, and an open structure.
Equal nozzle ceiling, hotter bed, smaller volume, no enclosure. That last one is the whole comparison for anyone who prints ABS or ASA, because those materials do not fail on nozzle temperature — they fail on the air around the part contracting faster than the part can hold together. Why ABS parts shrink and split works through that, and why prints warp covers the milder version you see with PETG.
The second thing the P1S wins is the shelf. Hardened hotends, plates in several surfaces, auxiliary cooling, touchscreens, printhead ducts, AMS units. None of it fits a FlashForge. P1S mods worth doing is the short version of what you would be walking away from.
What it gets right
- The enclosure plus auxiliary fan is what makes ABS and ASA realistic rather than aspirational
- Still the best-supported machine in the range for third-party upgrades — screens, hotends, plates, ducts
- Fast enough that the P2S's speed gain is not the reason to replace it
What it does not
- No touchscreen as shipped, which is why the Panda Touch exists
- No quick-swap nozzle: a nozzle change is a hotend job, not a 30-second one
- Passive chamber only — it holds heat, it does not make heat
| Released | July 13, 2023 |
|---|---|
| Type | Enclosed CoreXY |
| Over the P1P | Enclosure, auxiliary cooling fan and air filter |
| Multi-color | AMS and AMS 2 Pro (4 spools, expandable) |

Stock photograph of this product class, not of this specific unit.
#ad We earn a commission · price as of November 20, 2026
2. Best cheap four-color machine
FlashForge AD5X
Four spools with automatic color change included, at a 220 mm cube with a published 300 C nozzle and a 110 C bed. The color system is not an add-on purchase.
This is the machine behind the query. 3D Universe lists the AD5X at a 220 x 220 x 220 mm build volume, a 300 C maximum nozzle, a 110 C maximum bed, a four-spool IFS with automatic color change, a 4.3-inch touchscreen, an optional camera and an open structure, at 11 kg and 363 x 376 x 413 mm excluding the screen, feeder and spool holder.
Read that against an A1. 3DJake lists the A1 at a 256 mm cube, a 300 C nozzle and a 100 C bed, also open frame, with the AMS Lite sold separately or as the Combo. The two machines are doing the same job from the same starting position: open-air four-color printing in PLA and PETG. The AD5X is smaller in every axis and includes its color system; the A1 is larger and has an upgrade path that already exists.
Two honest cautions. The first is the speed figure: 3D Universe lists maximum printing at 300 mm/s with a 200 mm/s standard, while 3DJake lists the same machine at 600 mm/s. Those are not the same claim, and we have not measured either, so treat 600 as a headline rather than a working number. The second is the open structure. The 110 C bed is the hotter of the two beds here and it still will not make ABS behave in open air. Enclosure options is the Bambu answer to that; there is no equivalent third-party market for an AD5X.
What it gets right
- Four-spool automatic color change is included rather than a separate purchase
- A published 300 C nozzle and 110 C bed match a P1S's figures at a much lower price
- 11 kg and a 363 x 376 x 413 mm body make it the easiest machine here to find space for
What it does not
- Open structure, so ABS and ASA are not its job no matter what the nozzle ceiling says
- A 220 mm cube is smaller than every 256 mm Bambu machine, and the gap shows on large single parts
- Separate ecosystem: no AMS, no Bambu plate, no BIQU Panda part and no Bambu profile transfers
- I have not run one; everything on this site about it is published specification and reasoning, not observation
| Build volume | 220 x 220 x 220 mm |
|---|---|
| Type | Open-frame CoreXY, direct drive |
| Nozzle | 0.4 mm standard, to 300 C |
| Bed | To 110 C |
| Multi-material | IFS, four spools, automatic color change |
| Machine dimensions | 363 x 376 x 413 mm, excluding screen, IFS and spool holder |
| Net weight | 11 kg |
| Screen | 4.3-inch touchscreen |
| Camera | Optional |
| Nozzle diameters | 0.4 mm standard; 0.25, 0.6 and 0.8 mm optional |

Stock photograph of this product class, not of this specific unit.
#ad We earn a commission · price as of November 20, 2026
3. Best if purge waste is your real complaint
FlashForge Creator 5
Four independent toolheads at a 256 mm cube, so a material change does not purge the previous color through one shared nozzle.
This is the FlashForge machine that does something your AMS cannot. FlashForge lists the Creator 5 with four independent toolheads at a 256 x 256 x 256 mm build volume, a 320 C maximum nozzle, a 120 C maximum bed, up to 300 mm/s printing and 600 mm/s travel, up to 30,000 mm/s² acceleration, a built-in camera, a 4-inch touchscreen, below 55 dB in silent mode, and PVA and BVOH soluble supports among the recommended materials.
The architecture is the point. An AMS and a P1S share one nozzle, so every color change means pushing the old material out through it — which is where the purge tower comes from. Four toolheads each hold their own material at their own temperature, so a change is a mechanical swap rather than a flush. That is also what makes dissolvable support in a genuinely different polymer practical, which single-nozzle multi-color cannot do well. What dual nozzles actually change covers the same argument inside the Bambu range, where the answer stops at two.
The costs are real and worth stating plainly. FlashForge lists no active chamber heating on the standard Creator 5 — the 65 C heated chamber is the Pro — so a 320 C nozzle sits on an unheated open frame, which is a strange pairing for engineering material. Four toolheads is also four times the calibration and consumable surface. And it is a separate ecosystem: nothing on the upgrades roundup fits it.
What it gets right
- Four independent toolheads change material without purging the previous one through a shared nozzle
- Soluble support in a second material is a genuine capability a single-nozzle AMS machine cannot match
- The same 256 mm cube as a P1S, so parts that fit your current machine fit this one
What it does not
- Open frame with no active chamber heating, so the 320 C nozzle is further ahead of the enclosure than it looks
- Four toolheads is four of everything to calibrate, clean and eventually replace
- Separate ecosystem: nothing from a Bambu shelf fits it and no AMS attaches
- I have not run one; everything on this site about it is published specification and reasoning, not observation
| Build volume | 256 x 256 x 256 mm |
|---|---|
| Toolheads | Four independent |
| Nozzle | 0.4 mm standard, to 320 C |
| Bed | To 120 C |
| Speed | Up to 300 mm/s printing, up to 600 mm/s travel |
| Acceleration | Up to 30,000 mm/s2 |
| Machine dimensions | 436 x 432 x 480 mm without accessories; 520 x 443 x 710 mm with |
| Net weight | 14 kg |
| Screen | 4-inch 800 x 480 color touchscreen |
| Camera | Built-in, 1280 x 720 at 30 fps |
| Rated noise | Below 55 dB in silent mode |
| Chamber | No active heating; the Creator 5 Pro adds a 65 C heated chamber |

4. The in-family answer to the AD5X
Bambu Lab A1
A 256 mm open-frame bed with AMS Lite capability. If four-color PLA on a budget is the goal, this is the version that keeps you in the ecosystem.
If the AD5X appeals, this is the comparison that matters more than P1S versus AD5X. 3DJake lists the A1 at a 256 x 256 x 256 mm build volume, a 300 C nozzle, a 100 C bed, 465 x 410 x 430 mm and 8.3 kg, with AMS Lite capability for four open-air spools, sold separately or as the Combo.
Against the AD5X the A1 gives up the hotter bed and the included color system, and wins a bigger bed in every axis plus the part of this site that is not a specification: the plates, the hotends, the printed accessories, the profiles and the resale market. Combo versus base is the honest read on whether to buy the color system with the machine, and A1 and A1 mini mods worth doing is what the ecosystem gets you afterward.
What neither machine does is ABS. Both are open frame with no active chamber heating, and that is the single reason A-series owners end up on upgrading from an A1.
What it gets right
- Larger build area than the A1 mini for very little extra money or desk space
- The two-tower gantry is noticeably more rigid than a single-upright bed slinger
- Adding the AMS Lite — separately or by buying the Combo — makes four-color PLA and PETG genuinely practical
What it does not
- Still open-frame — this is the single thing that will eventually make you upgrade
- Bed slinger kinematics mean it will never match a CoreXY machine on tall, fast prints
- No active chamber heating, so ABS and ASA warp without an aftermarket enclosure
| Released | December 14, 2023 |
|---|---|
| Type | Open-frame bed slinger, two-tower gantry |
| Multi-color | AMS Lite capable (4 spools, open air) — sold separately or as the Combo |
Questions people actually ask
Is the FlashForge AD5X better than a Bambu Lab A1?
It depends entirely on whether size or an included color system matters more. 3D Universe lists the AD5X at a 220 x 220 x 220 mm build volume with a four-spool IFS included, a 300 C nozzle and a 110 C bed. 3DJake lists the A1 at a 256 x 256 x 256 mm volume, a 300 C nozzle and a 100 C bed, with the AMS Lite sold separately or as the Combo. The AD5X gives you color for less; the A1 gives you a bigger bed and the whole Bambu parts and profile ecosystem. Both are open frame, so neither handles ABS or ASA.
Is the FlashForge AD5X enclosed?
No. The 3D Universe listing describes it as an open structure. That is the most important line in its specification for anyone considering it against a P1S, because ABS and ASA need warm, still air around the part rather than a hotter nozzle - and the AD5X's 110 C bed, hotter than either Bambu bed here, does not change that.
What is the difference between the FlashForge AD5X and the Adventurer 5M?
The AD5X is the four-color machine; the Adventurer 5M is the single-material predecessor. 3DJake lists the 5M at the same 220 x 220 x 220 mm build volume but a lower 280 C nozzle, with a 110 C bed, open frame and a 363 x 402 x 448 mm body. The 5M is shown sold out at that retailer, so if you are comparing a Bambu A1 against an Adventurer 5M, the current equivalent to shortlist is the AD5X.
Does the FlashForge Creator 5 waste less filament than an AMS?
By design, yes, because it does not purge. FlashForge lists four independent toolheads, so each material stays loaded in its own hotend and a change is a mechanical swap rather than a flush through one shared nozzle. An AMS, AMS 2 Pro or AMS Lite all share one nozzle, which is where the purge tower comes from. We have not measured the difference on either system and do not claim a figure for it.
Can the FlashForge Creator 5 print dissolvable supports?
FlashForge lists PVA and BVOH among the recommended materials, and four independently heated toolheads are what makes a soluble support material practical - it stays hot in its own head instead of being flushed through a shared nozzle every few layers. That is a capability a single-nozzle four-spool system does not really have.
Will my Bambu accessories work on a FlashForge printer?
No. Nothing transfers - not build plates, not hotends, not the AMS or AMS Lite, not any BIQU Panda part, and not your slicer profiles. That ecosystem cost is easy to miss in a specification table and easy to feel in the second week of ownership.
Is the Creator 5 a replacement for a Bambu Lab P2S?
Only if multi-material is the whole reason you are buying. They share a 256 x 256 x 256 mm build volume, and FlashForge lists a hotter 320 C nozzle and 120 C bed against the P2S's published 300 C and 110 C. But 3DJake lists the P2S as enclosed, and FlashForge puts active chamber heating on the Creator 5 Pro rather than the standard Creator 5. For ABS and ASA the enclosed machine is still the right one.
How fast is the FlashForge AD5X really?
The published figures disagree, so treat the headline with caution. The 3D Universe listing gives a maximum printing speed of 300 mm/s with a 200 mm/s standard, while the 3DJake listing for the same machine gives 600 mm/s with 20,000 mm/s2 acceleration. Both are retailer-published and we have not timed the machine, so no single number is asserted here.
Sources
- FlashForge AD5X build volume (220 x 220 x 220 mm), 300 C maximum nozzle and 110 C maximum bed, machine dimensions 363 x 376 x 413 mm excluding screen, IFS and spool holder, 11 kg net weight, four-spool IFS, 4.3-inch touchscreen, optional camera, open structure, 0.4 mm standard nozzle with 0.25, 0.6 and 0.8 mm optional, and "In-Stock Now" availability - 3D Universe AD5X listing, retrieved 2026-10-24
- FlashForge AD5X listed at 600 mm/s maximum speed and 20,000 mm/s2 acceleration against the 300 mm/s printing figure the 3D Universe listing gives, plus the stated material list (PETG, PLA, TPU95A, PLA-CF, PETG-CF) and direct drive extruder - 3DJake AD5X listing, retrieved 2026-10-24. The same page shows the machine sold out at that retailer, which is why the availability check above rests on 3D Universe instead
- FlashForge Creator 5 build volume (256 x 256 x 256 mm), four independent toolheads, 320 C maximum nozzle, 120 C maximum bed, up to 300 mm/s printing and up to 600 mm/s travel, up to 30,000 mm/s2 acceleration, machine dimensions 436 x 432 x 480 mm without accessories and 520 x 443 x 710 mm with, 14 kg net weight, 4-inch 800 x 480 touchscreen, built-in 1280 x 720 at 30 fps camera, below 55 dB in silent mode, PVA and BVOH soluble support among the recommended materials, no active chamber heating with a 65 C heated chamber on the Creator 5 Pro, and "In Stock" availability - FlashForge Creator 5 product page, retrieved 2026-10-24
- FlashForge Adventurer 5M build volume (220 x 220 x 220 mm), 280 C maximum nozzle, 110 C maximum bed, 600 mm/s and 20,000 mm/s2, direct drive extruder, open frame, 4.3-inch touchscreen and device size 363 x 402 x 448 mm without the spool holder, plus the existence of a 5M Pro at 380 x 400 x 453 mm - 3DJake Adventurer 5M listing, retrieved 2026-10-24. The 5M is shown sold out at that retailer and carries no buy row on this page for that reason
- P1S build volume (256 x 256 x 256 mm), machine dimensions (389 x 389 x 458 mm), net weight 12.95 kg, 300 C nozzle and 100 C bed - Makerpoint P1S listing, retrieved 2026-10-11
- A1 build volume (256 x 256 x 256 mm), device dimensions (465 x 410 x 430 mm), net weight 8.3 kg, 100 C bed and 300 C nozzle - 3DJake A1 listing, retrieved 2026-10-11
- P2S build volume (256 x 256 x 256 mm), machine dimensions (392 x 406 x 478 mm), net weight 14.9 kg, 300 C nozzle, 110 C bed and the absence of an active chamber heater - 3DJake P2S listing, retrieved 2026-10-11
- Feature rows for the AMS units, the hardened hotends and the fitment rows on every third-party part come from this site's product registry, whose spec provenance is documented in content/products.ts - no figure is asserted that a manufacturer or a cited third party did not publish
Read this next
- Bambu Lab P1S vs Elegoo Centauri CarbonIdentical 256 mm cubes. Elegoo publishes 350 C and 110 C against the P1S's 300 C and 100 C. The P1S wins on AMS, parts and profiles.
- Bambu Lab vs the Creality K2 PlusThe K2 Plus Combo publishes 350 x 350 x 350 mm, a 350 C nozzle, a 120 C bed and a 60 C heated chamber. Bambu answers with ecosystem and footprint.
- Dual nozzles, AMS and hotend swapping explainedDual nozzle, AMS and automatic hotend swapping compared - what each actually does and which models have which.
- Combo or base printer: is the AMS bundle worth it?What a Combo actually contains, the one fitment rule that decides whether you can add an AMS later, and how to work out which way round is cheaper on the day you buy.
- Bambu Lab X1C vs X1EThe X1E was the X1C with an actively heated 60 C chamber, a 320 C nozzle and enterprise networking. Both ended production in March 2026; the X2D is the successor.
- The best Bambu Lab printer for multicolorThe printer matters less than the AMS that fits it. The P1S plus AMS 2 Pro is the setup to beat, and the A1 plus AMS Lite is the cheap route in.